What size are 700R4 cooler lines?
4L65E / 700R4 / 4L60 / 4L60E Cooler Line Fitting, 5/16″ x 1/4″ (82-Up)
Can you run a 700R4 transmission without a computer?
To run a 700-R4 trans behind a carbureted engine without a computer, at the very least the TV cable must be hooked up to the carburetor and properly adjusted. Not just a simple kickdown cable like your TH350 analogue, the TV cable controls line pressure and shift points.
What size is transmission cooler line?
It’s usually 3/8″ OD. There is a port on the driver side of the transmission right above the shifter shaft. It’s 1/8″ npt and a sensor will thread right in.
What size are transmission cooler line fittings?
Transmission Radiator end of fitting has 1/4″ MPT. line fitting is 1/2″-20 inverted flare INS. – Factory fitting remains with recessed internal threads.
Does a 700R4 need a cooler?
Yes, it needs a cooler, but the in-radiator cooler is adequate for most stock applications. It does not need to run the fluid through the cooler when in OD since the converter is locked up in this configuration.
What size are the fittings on 700R4 transmission?
-6 x 1/4NPS is the correct size for GM turbo 350, Turbo 400, 700R4, 4L60E and many other GM transmissions.
What diameter is a transmission line?
Components of the Transmission System They are usually about one or two inches in diameter. There is also a smaller wire at the top of the structure, called a shield wire.
What size are transmission fluid lines?
Flare, full thread. I.D.-3/8″ O.D. Line with a 3/4″ style with rubber hose/metal line. I.D. – Line snaps into fitting and is I.D.-3/8″ O.D.
What speed should 700R4 shift at?
We will say that, when properly adjusted, the First-to-Second shift should occur at 15-20 mph; Second-to-Third shift at 25-30 mph; and Third-to-Fourth shift at 40-45 mph.
What is the plug on the side of a 700R4?
the plug on the left side only controls the converter clutch. you really need to use the lock up feature,if not you will eventually burn up the trans. if you do a lot of interstate driving.as the converter will not get any cooling lube with the lockup feature not working.
Will 700R4 hold up to 450 hp?
supports up to 450HP. Our Street Cruiser series exceeds many of our competitors’ best and is our least expensive GM transmission. Suitable for most street or track applications, it’s rated at 450 RWHP…
How to set the TV cable on a 700R4?
universal TV Cable (TCI® 376800) that is designed to work correctly in any 700R4/2004R application. Step 2 With the carburetor/throttle body end of the TV Cable disconnected, pull the link out of the transmission and fit the cable end to the link as shown in Figure 1. Push the TV Cable sheath into the seal in the
What transmission fluid do I use in a 700R4?
When installing the converter onto the transmission, please pour approximately one quart of ATF (automatic transmission fluid) into the converter before installing into the transmission. What transmission fluid do I use in a 700R4? This transmission can store about 11 quarts of transmission fluid and its recommended fluid is DEXRON VI.
How do you tell the difference between 700R4 and 4L60E?
– Six bolts are now used to connect the tail shaft. – They only have three different types of bell-housings in North America. The most common of these is the 90 degree V6 and V8 Bellhousing. – This version, as well as the 93-97 4L60E use a 298mm input shaft /torque converter. – The vehicle speed sensor is still on the passenger side of the tail-shaft.
How do you adjust a 700R4 transmission?
Transmission oil level. Correct if necessary.