How old is my Franklin Electric well pump?
The serial number on all Franklin Electric motors can be found etched/engraved into the motor stator shell, just above the etched nameplate information. The first two digits in the date code represent the year of manufacture, with the third being the month of manufacture.
Where are Franklin well pumps made?
Franklin Electric Inc. of Blufton, Indiana, is the world’s leading producer of submersible motors, which are used primarily for pumping systems in water wells, underground diesel and gasoline storage, and wastewater systems.
What is the warranty on a Franklin well pump?
(1) 5 years (60 months) from date of installation or 66 months from manufacture date code, whichever occurs first. Must be installed with Franklin Electric motor and Franklin Electric control box or SubDrive….Pump Products.
| 4″ Standard Capacity Pumps/Pump Ends | 60 months/66 months(1) |
|---|---|
| Surface Pumps up to 2 hp | 36 months(5) |
How do you reset a Franklin Electric control box?
The unit must be manually reset by removing power for 10 seconds. (If you have a Pumptec remote control, this will be indicated by overload in the Pumptec Fault History.) Voltage Indicator Light When the voltage light is solid, an under voltage condition has been detected.
What is the warranty on a submersible pump?
1. Baldor-Reliance Tandem Seal Submersible Motor is warranted for a period of five years from date of shipments to the Original Buyer, to be free from defects in material and workmanship and to conform to any applicable drawings and specifications approved by Baldor Electric Company. 2.
Can you run a well pump without a control box?
The short answer is yes. Most pumps will work without a control box. But here’s the rub – if you want your pump to run better, for more hours in the day, if you want to use a float switch, and if you want to protect your pump from voltage and current spikes, then a control box is an excellent addition to your system.
Are ridgid sump pumps made by Wayne?
Wayne Systems are the only manufacturers for rigid submersible sump pumps.
How long can you run a well pump?
In most cases, your home’s well pump should last around 10 years without worry, but like any electric machine, it’s important to take care to ensure it lasts.
Who owns Franklin Electric?
As of 2020, the company employed 5,400 individuals worldwide….Franklin Electric.
| Type | Public |
|---|---|
| Key people | Gregg Sengstack (Chairman of the Board and CEO) |
| Revenue | 1.662 billion (2021) |
| Number of employees | 5,400 (2020) |
| Website | www.franklin-electric.com |
Where are Franklin well pumps manufactured?
What size breaker do I need for a well pump?
How Many Amp Breaker Should A Well Pump Have?
| Well Pump (HP) | Volts | Req. Circuit Breaker (Amps) |
|---|---|---|
| 0.5 HP | 110V | 15A |
| 0.5 HP | 230V | 15A |
| 0.75 HP | 230V | 20A |
| 1 HP | 230V | 25A |
Is a 2-wire or 3 wire well pump better?
For most residential applications the preference of a 2-wire versus a 3-wire motor is usually up to the installer and homeowner. Under 1.5 horsepower, a 2-wire motor can be recommended by some installers due to the ease of installation, reduced maintenance, extended life of starting components, and cost advantages.
Does a well pump use a lot of electricity?
Well pumps use a huge amount of energy every time they start up. Well pumps should be sized by a professional. It is not uncommon for people to have 3/4 hp pumps installed in their wells equaling 30 minutes of pumping per day or 350 kWh/yr, while a ½ hp pump, which uses only 240 kWh/yr, would be sufficient.
How do you tell if my well pump is 110 or 220?
The control box has the power cables that go to the submersible well pump. Above ground pumps will have a label on the motor that has a label. The label should indicate the voltage, most likely 220 or 230 volts and the horsepower or current draw (in amps) of the pumping equipment.